Print Shortlink

Instruction to Authors

The Journal Engineering Science (JES) – Guidelines for Authors

 Authors: Only papers that have not been published elsewhere are considered.Authors must follow the “The Journal Engineering Science (JES) … Guidelines for Authors” when submitting papers. Only individual persons but not company or organization can be author(s). As JES consists mainly of personal members, authors are required to submit their papers in their personal names. Once the paper is submitted, the name of authors cannot be changed, added or deleted.

 Deadline: No deadline for paper submission is specified.

 Papers Submission: The manuscript of the paper (3 copies) should be submitted to the Chief/Executive Editor of the Journal JES. Online submission in the E-mail addresses to the Chief/Executive Editor is also highly encouraged and accepted.

 Purpose of Reviewing: The submitted paper is peer-reviewed to judge its quality for the journal JES. The Editorial Bored may ask authors to make revisions of the paper to satisfy the requirement. It should be noted, however, that the author is inherently responsible for the quality of the published paper.

Reviewer: The Editorial Board assigns three reviewers expertise in the relevant areas for each paper based on the contents.

Judgment by Reviewer: Based on the evaluation and comparison with past published papers in elsewhere, the reviewer judges whether the paper is to be accepted or rejected. The reviewer should try to be accepted a paper that can contribute to the future academic/ technological development, even if it has some drawbacks. When the reviewer recommends rejection, reasons should be given according to the items mentioned in the prescribed format of Paper Review Report. The results of review are to be described and communicated to the author(s) in detail regardless of its acceptance or rejection.

Decision by Editorial Board: The Editorial Board judges if paper is to be accepted based on the reports by three reviewers. In principle, if two or more of the three reviewers recommend the acceptance, the paper will be accepted. If any reviewer requires a revision on the paper, the Editorial Board may request author to revise the paper. Editorial Board will review the revised paper to judge whether the author has given satisfactory revision and response to the comments by reviewer. The reviewer may be requested to re-review the paper for this purpose. The Editorial Board has responsibility in its final judgment, and notifies the decision promptly to the concerned.

Dead Line for Receiving Revised Manuscript: If the Editorial Board does not receive the revised manuscript and/or communication from the author within 16 weeks after the request of revision, the paper is treated as rejected.

 How to Prepare a Manuscript:

  • Page size must be A4 (210mmÍ297mm)
  • Top, bottom & sides margins must be 25mm
  • For all text we recommend 10 point Times New Roman excepted Manuscript Title, single spacing without any incident

Manuscript Title: The title of the paper should be at the top of the page, Boldface Capital, 12-point, alignment center. The title included in the Manuscript must reflect the revised title as agreed to by the Editorial Board.

Authors Names: Will follow the Title, 10 point Bold, alignment center, 20 pt space before and 5 pt space after. The names should appear as a comma separated list with numbering as above.

Authors Information: Will follow the Authors’ Names, 10-point italic, alignment center.

Abstract: Subtitle “ABSTRACT”, Boldface Capital, 10-point, alignment left, 20pt space before and 5 pt space after. An abstract in single column of less than 150 words is required. The body of your abstract, written in 10-point italic single spaced with justification on both sides. The abstract should state the papers purpose, methods or procedures, new results and conclusions. It should not include tables, figures, equations, nonstandard abbreviations or anything that is not contained in the main text.

Keywords: Subtitle “Keywords:,  Boldface Title case (i.e., using capital letters 1st letter of each word), 10-point, alignment left, 10 pt space before. The number of key words should be limited to 6, 10 pt, Italic, Title case, separated by coma and should be alphabetical in order.

Heading: For all heading Arabic numbers should be used followed by a 12mm space tab, Boldface Capital, 10-point, flash left, 20 pt space before and 5 pt space after. (example: 1. INTRODUCTION)

Subheading 1: Subheading 1 have a training section numeric number followed by a 12 mm space tab, Boldface Title case, 10-point, flush left, 20 pt space before and 5 pt space after. (example: 1.1 Subtitle)


(i) All manuscripts must be written in English and the original type script for a Review article and Full paper should be typed on one side of good quality offset paper, with double spacing and a wide margin and be submitted in duplicate to the Chief or Executive Editors.

(ii) The manuscript of Full paper should be limited with in 12 type written pages (double spaced) including tables, figures, graphs, etc. The title page should contain title, author(s) name, address(es) , abstract, PACS Nos. and Keywords. The main Text should start on a new page. All pages should be numbered. The paper should be divided into sections starting preferably with Introduction and ending with Conclusions.

(iii) Rapid communication is devoted to the announcement of timely and important results. While that a short communication should not exceed 4 pages. The should follow the same style and format as the full paper except that they need not be divided into sections.

(iv) Manuscript in duplicate, of which one is a clear master copy with original figures and also a soft copy ( the  Text in XP2000 or higher version and Figures in post script Files) should be send to the Editor  in  the address mentioned below with a mention of the field under which the paper is being submitted.

Title: The title of the paper should be brief and specific. The authors should prepare the manuscripts in such a way that there should be a title page with only the names of the authors and their address. The second page should carry the title of the paper with Abstract to be followed by introduction etc.

Abstract: An abstract of less than 150 words is required. It should include only the gist of the paper. Abstract is not the summary and in no case it should contain the subject of the Materials and Methods, and/or any descriptive part of the paper.

Keywords and PACS number: Appropriate Keywords and PACS Nos. (Physics and Astronomy Classification Scheme of American Institute of Physics) (not more than three) must be provided for indexing and information retrtrieval services.

Text: The authors should pay attention to the language, logical presentation, enumeration of assumption made, justifications of approximation made etc and all the limitation must be stated wherever or necessary. Moreover, a paper must be self contained, its presentation being class and satisfactory.

Tables, Graphs and Figures: The paper should contain minimum number of tables, graphs and figures. Each figure must be referred to in the text, be numbered and have a caption. The same data should not be used both for the tables and for the graphs and figures. The appropriate place of the figure should be indicated in the margin of the text. Axes of the figures must be labeled properly.

Formulae: Displayed formula should be numbered and typed unambiguously, vectors, special symbol’s, subscript and superscripts, etc. should be identified with proper signs in the manuscript. Long equations should be avoided as much as possible, by introduction of suitable abbreviations of component expressions.

Reference: All reference should be arranged at the end of the text according to alphabetical order of the author’s last name and followed by the year, abbreviated name of the Journal, volume number and after colon page number for example.

[1] Sikder S. S. and M. A. Asgar; Thermochimica Acta 326 (1999); pp119-126.

[2] Atsumi T., T. Isihara, M. Koyama and M. Matsuzawa; Phys. Rev. A42 (1990) p.6391.

[3] Herzer G.; IEEE Trans. Magn. 26, pp.1397-1402 (1990)

[4] Wendlandt W. W.; Thermal Analysis, Wiley Inter science, New York, 3rd edn. 1986, chap.1

The references cited should be limited to the absolute minimum and the list to the sumitted in a separate sheet containing names of all authors (et. al. is not allowed).

Nomenclature, abbreviation and symbols, etc. are confined in International standard.